Silicone-free and dispensable: MTC introduces a new 1C gap filler for optimized heat management

With the new TCTP series, MTC Micro Tech Components GmbH presents a silicone-free, thermally conductive one-component gap filler based on acrylic. The dispensable paste offers a very high thermal conductivity and can be used in applications where the use of silicone is critical. For example, at car manufacturers it is imperative to avoid silicone, because of outgassing issues, until the end of painting plant. This is to ensure the optimum adhesion of the paint and to prevent paint wetting problems.

In the electrical and electronics industry, all contacts (e.g. switches and relays) are affected because the volatile constituents of silicone settle on the contact surfaces and can have an electrically insulating effect, which can lead to malfunctions of such components.

The silicone-free 1C gap filler TCTP is designed for a wide working range in temperature from -40 to +130 °C. It is ideal for effective heat dissipation of electrical or electronic components in a variety of application areas, such as Industry 4.0 / IoT, automotive, power electronics, energy storage, rail technology, telecommunications, LED lighting, medical technology, industrial computers, and so on.

The pasty high-performance gap filler TCTP is available in standard cartridges for manual or automated dispensing in dosing devices. This means that particularly thin adhesive joints can be applied, which ensure the seamless thermal connection between the heat source (component e.g. processor) and the heat sink (heat sink, circuit board or chassis). Even with complex designs, the flexible 1-component gap filler compensates air gaps, uneven surfaces and component tolerances up to 3 mm, so that effective cooling can be achieved.
The dispensable paste also gives the developer greater freedom in designing the spacing and shape of the heat-conducting material. The new silicone-free TCTP series from MTC achieves a high thermal conductivity of up to 5.0W/mK (watts per meter and Kelvin). Without using the 1C gap filler material, only air, with an extremely low thermal conductivity (0,0262W/mK), would be available for the heat transfer. Even smooth-appearing contact surfaces between the heat source and the heat sink actually only touch about 20%. These micro bumps and bulges form heat-insulating air cavities. Due to the use of the thermally highly conductive 1C-Gap-Filler material, the heat dissipation is optimized. The RGT rule illustrates how essential optimal heat management and protection against overheating is for the lifespan of electronic components, which simply states that if the operating temperature is reduced by 10K, the lifespan roughly doubles.

The dispensable and silicone-free 1C gap filler from MTC enables the establishment of highly thermally conductive form-in-place connections. The pasty heat-conducting material adapts flexibly to the respective surfaces and component shape, has a very good compressibility and convinces with excellent dosing properties. Since when assembling the cooling device the full thermal conductivity is achieved with very low contact pressure and also permanently low mechanical forces act on components and circuit boards. The TCTP series is particularly suitable for use with sensitive component groups, but also for plug-in cooling solutions with low clamping forces.

The silicone-free 1-component gap filler remains tough and elastic even after curing at room temperature, does not dry out and is resistant to water and most acids, alkalis and organic substances. Unopened cartridges can be stored for up to 12 months (shelf life). In regard to flammability, the TCTP series is certified according to UL94 with a flammability classification of V-0. Thermally conductive materials from MTC meet the highest quality and safety standards for reliable and long-term use and are subject to strict controls during production.

For electrical isolation and as a spacer between the heat source and the heat sink, MTC offers the silicone-free 1C-Gap-Filler TCTP optionally with added glass beads, which ensure a minimum insolation distance and thus avoid short circuits.

In addition to the presented silicone-free 1C gap fillers of the TCTP series, MTC Micro Tech Components GmbH also offers silicone-free gap pads (TCGF series) with an equally high thermal conductivity of up to 5.0 W / mK and material thicknesses of 0.5 - 5 mm. In addition, the product portfolio of thermally conductive materials includes industrial thermal pastesthermally conductive insulators and double-sided adhesive tapesphase change materials (PCM) and graphite foils. Moreover, MTC is also a producer and solution provider for components in the field of EMC (electromagnetic compatibility).
For the successful implementation of complex and demanding applications, customers and system developers benefit from comprehensive services, many years of experience and extensive know-how. MTC Micro Tech Components GmbH, headquartered in Dillingen / Donau, Bavaria, convinces customer as a global supplier for almost all industrial sectors with its own development and laboratory capacities as well as production and sales locations in Germany, Hong Kong and South Korea.  

Give us a call:
+49 [0] 90 71 - 79 45 - 0
Contact us: